diff --git a/README.md b/README.md index 0a9cd770c..b82a88955 100644 --- a/README.md +++ b/README.md @@ -26,9 +26,9 @@ TinyUSB is an open-source cross-platform USB Host/Device stack for embedded syst The stack supports the following MCUs - **Nordic:** nRF52840 -- **NXP:** LPC11Uxx, LPC13xx, LPC175x_6x, LPC177x_8x, LPC18xx, LPC40xx, LPC43xx, LPC51Uxx +- **NXP:** LPC Series: 11Uxx, 13xx, 175x_6x, 177x_8x, 18xx, 40xx, 43xx, 51Uxx - **MicroChip:** SAMD21, SAMD51 (device only) -- **ST:** STM32 series: L0, F0, F2, F3, F4, F7, H7 (device only) +- **ST:** STM32 series: L0, F0, F1, F2, F3, F4, F7, H7 (device only) [Here is the list of supported Boards](docs/boards.md) that can be used with provided examples. diff --git a/docs/boards.md b/docs/boards.md index b6b48a7f1..0b38cf568 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -46,6 +46,7 @@ This code base already had supported for a handful of following boards - [STM32 L035c8 Discovery](https://www.st.com/en/evaluation-tools/32l0538discovery.html) - [STM32 F070rb Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f070rb.html) - [STM32 F072rb Discovery](https://www.st.com/en/evaluation-tools/32f072bdiscovery.html) +- STM32 F103c Blue Pill - [STM32 F207zg Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f207zg.html) - [STM32 F303vc Discovery](https://www.st.com/en/evaluation-tools/stm32f3discovery.html) - [STM32 F407vg Discovery](https://www.st.com/en/evaluation-tools/stm32f4discovery.html) diff --git a/hw/bsp/stm32f103bluepill/board.mk b/hw/bsp/stm32f103bluepill/board.mk new file mode 100644 index 000000000..4758edf17 --- /dev/null +++ b/hw/bsp/stm32f103bluepill/board.mk @@ -0,0 +1,53 @@ +CFLAGS += \ + -DHSE_VALUE=8000000 \ + -DSTM32F103xB \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m3 \ + -mfloat-abi=soft \ + -nostdlib -nostartfiles \ + -DCFG_TUSB_MCU=OPT_MCU_STM32F1 + +# mcu driver cause following warnings +#CFLAGS += -Wno-error=unused-parameter + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F1xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F1xx + +# All source paths should be relative to the top level. +LD_FILE = $(ST_CMSIS)/Source/Templates/gcc/linker/STM32F103XB_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32f1xx.c \ + $(ST_HAL_DRIVER)/Src/stm32f1xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32f1xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32f1xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32f1xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32f1xx_hal_gpio.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f103xb.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = stm32_fsdev + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM3 + +# For flash-jlink target +JLINK_DEVICE = stm32f303vc +JLINK_IF = swd + +# Path to STM32 Cube Programmer CLI, should be added into system path +STM32Prog = STM32_Programmer_CLI + +# flash target using on-board stlink +flash: $(BUILD)/$(BOARD)-firmware.elf + $(STM32Prog) --connect port=swd --write $< --go diff --git a/hw/bsp/stm32f103bluepill/stm32f103bluepill.c b/hw/bsp/stm32f103bluepill/stm32f103bluepill.c new file mode 100644 index 000000000..aade44d35 --- /dev/null +++ b/hw/bsp/stm32f103bluepill/stm32f103bluepill.c @@ -0,0 +1,182 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32f1xx.h" +#include "stm32f1xx_hal_conf.h" + +#define LED_PORT GPIOC +#define LED_PIN GPIO_PIN_13 +#define LED_STATE_ON 0 + +#define BUTTON_PORT GPIOA +#define BUTTON_PIN GPIO_PIN_0 +#define BUTTON_STATE_ACTIVE 1 + + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSE) + * SYSCLK(Hz) = 72000000 + * HCLK(Hz) = 72000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 2 + * APB2 Prescaler = 1 + * HSE Frequency(Hz) = 8000000 + * HSE PREDIV1 = 1 + * PLLMUL = 9 + * Flash Latency(WS) = 2 + * @param None + * @retval None + */ +void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef clkinitstruct = {0}; + RCC_OscInitTypeDef oscinitstruct = {0}; + RCC_PeriphCLKInitTypeDef rccperiphclkinit = {0}; + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + oscinitstruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + oscinitstruct.HSEState = RCC_HSE_ON; + oscinitstruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1; + oscinitstruct.PLL.PLLMUL = RCC_PLL_MUL9; + oscinitstruct.PLL.PLLState = RCC_PLL_ON; + oscinitstruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + HAL_RCC_OscConfig(&oscinitstruct); + + /* USB clock selection */ + rccperiphclkinit.PeriphClockSelection = RCC_PERIPHCLK_USB; + rccperiphclkinit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5; + HAL_RCCEx_PeriphCLKConfig(&rccperiphclkinit); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + clkinitstruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + clkinitstruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + clkinitstruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + clkinitstruct.APB1CLKDivider = RCC_HCLK_DIV2; + clkinitstruct.APB2CLKDivider = RCC_HCLK_DIV1; + HAL_RCC_ClockConfig(&clkinitstruct, FLASH_LATENCY_2); +} + +void board_init(void) +{ + #if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + #endif + + SystemClock_Config(); + + // Notify runtime of frequency change. + SystemCoreClockUpdate(); + + // LED + __HAL_RCC_GPIOC_CLK_ENABLE(); + GPIO_InitTypeDef GPIO_InitStruct; + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + __HAL_RCC_GPIOA_CLK_ENABLE(); + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_PULLDOWN; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // USB Pins + // Configure USB DM and DP pins. + __HAL_RCC_GPIOA_CLK_ENABLE(); + GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + // USB Clock enable + __HAL_RCC_USB_CLK_ENABLE(); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +} + +uint32_t board_button_read(void) +{ + return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +#ifdef USE_FULL_ASSERT +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(char *file, uint32_t line) +{ + /* USER CODE BEGIN 6 */ + /* User can add his own implementation to report the file name and line number, + tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + /* USER CODE END 6 */ +} +#endif /* USE_FULL_ASSERT */ + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32f103bluepill/stm32f1xx_hal_conf.h b/hw/bsp/stm32f103bluepill/stm32f1xx_hal_conf.h new file mode 100644 index 000000000..a4a3f3086 --- /dev/null +++ b/hw/bsp/stm32f103bluepill/stm32f1xx_hal_conf.h @@ -0,0 +1,379 @@ +/** + ****************************************************************************** + * @file USB_Device/HID_Standalone/Inc/stm32f1xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration template file. + * This file should be copied to the application folder and renamed + * to stm32f1xx_hal_conf.h. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F1xx_HAL_CONF_H +#define __STM32F1xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/* #define HAL_ADC_MODULE_ENABLED */ +/* #define HAL_CAN_MODULE_ENABLED */ +/* #define HAL_CAN_LEGACY_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED */ +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +#define HAL_EXTI_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_PCCARD_MODULE_ENABLED */ +#define HAL_PCD_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SD_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_SPI_MODULE_ENABLED */ +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) +#if defined(USE_STM3210C_EVAL) + #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ +#else + #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ +#endif +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE 8000000U /*!< Value of the Internal oscillator in Hz */ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE 40000U /*!< LSI Typical Value in Hz */ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ + +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE 32768U /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE 3300U /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY 0x00U /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 1U + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1U */ + +/* ################## Ethernet peripheral configuration ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB 8U /* 8 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ + +/* DP83848 PHY Address*/ +#define DP83848_PHY_ADDRESS 0x01U +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY 0x000000FFU +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY 0x00000FFFU + +#define PHY_READ_TO 0x0000FFFFU +#define PHY_WRITE_TO 0x0000FFFFU + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ + +#define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ +#define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ +#define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ + +#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ +#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ + +#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ +#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ + +#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ +#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 1U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f1xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f1xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED + #include "stm32f1xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f1xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f1xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED + #include "Legacy/stm32f1xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f1xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f1xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f1xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f1xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f1xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32f1xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32f1xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f1xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f1xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f1xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f1xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f1xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_PCCARD_MODULE_ENABLED + #include "stm32f1xx_hal_pccard.h" +#endif /* HAL_PCCARD_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32f1xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32f1xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f1xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f1xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f1xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f1xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f1xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f1xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f1xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f1xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F1xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index c33f9b865..ec182960e 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -261,6 +261,12 @@ void dcd_int_enable (uint8_t rhport) NVIC_EnableIRQ(USB_HP_CAN_TX_IRQn); NVIC_EnableIRQ(USB_LP_CAN_RX0_IRQn); NVIC_EnableIRQ(USBWakeUp_IRQn); +#elif CFG_TUSB_MCU == OPT_MCU_STM32F1 + NVIC_EnableIRQ(USB_HP_CAN1_TX_IRQn); + NVIC_EnableIRQ(USB_LP_CAN1_RX0_IRQn); + NVIC_EnableIRQ(USBWakeUp_IRQn); +#else + #error Unknown arch in USB driver #endif } @@ -275,9 +281,14 @@ void dcd_int_disable(uint8_t rhport) NVIC_DisableIRQ(USB_HP_CAN_TX_IRQn); NVIC_DisableIRQ(USB_LP_CAN_RX0_IRQn); NVIC_DisableIRQ(USBWakeUp_IRQn); +#elif CFG_TUSB_MCU == OPT_MCU_STM32F1 + NVIC_DisableIRQ(USB_HP_CAN1_TX_IRQn); + NVIC_DisableIRQ(USB_LP_CAN1_RX0_IRQn); + NVIC_DisableIRQ(USBWakeUp_IRQn); #else #error Unknown arch in USB driver #endif + // CMSIS has a membar after disabling interrupts } @@ -822,7 +833,7 @@ void USB_IRQHandler(void) dcd_fs_irqHandler(); } -#elif (CFG_TUSB_MCU) == (OPT_MCU_STM32F1) +#elif CFG_TUSB_MCU == OPT_MCU_STM32F1 void USB_HP_IRQHandler(void) { dcd_fs_irqHandler(); @@ -854,14 +865,16 @@ void USB_LP_CAN_RX0_IRQHandler(void) { dcd_fs_irqHandler(); } + // USB wakeup interrupt (Channel 42): Triggered by the wakeup event from the USB // Suspend mode. void USBWakeUp_IRQHandler(void) { dcd_fs_irqHandler(); } + #else -#error Which IRQ handler do you need? + #error Which IRQ handler do you need? #endif #endif diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index bbaa52eae..36dca8cd8 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -57,7 +57,9 @@ #define PMA_LENGTH (512u) // NO internal Pull-ups // *B, and *C: 2 x 16 bits/word - #error The F102/F103 driver is expected not to work, but it might? Try it? + + // F1 names this differently from the rest + #define USB_CNTR_LPMODE USB_CNTR_LP_MODE #elif defined(STM32F302xB) || defined(STM32F302xC) || \ defined(STM32F303xB) || defined(STM32F303xC) || \