move irq for stm32 fsdev

hw/bsp/adafruit_clue/adafruit_clue.c

@@ -43,10 +43,9 @@ void USBD_IRQHandler(void)
   tud_irq_handler(0);
 }
 
-
+//--------------------------------------------------------------------+
-/*------------------------------------------------------------------*/
+// MACRO TYPEDEF CONSTANT ENUM
-/* MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
- *------------------------------------------------------------------*/
 #define _PINNUM(port, pin)    ((port)*32 + (pin))
 
 #define LED_PIN         _PINNUM(1, 1)

hw/bsp/stm32f070rbnucleo/stm32f070rbnucleo.c

@@ -25,9 +25,19 @@
  */
 
 #include "../board.h"
-
 #include "stm32f0xx_hal.h"
 
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USB_IRQHandler(void)
+{
+  tud_irq_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
 #define LED_PORT              GPIOA
 #define LED_PIN               GPIO_PIN_5
 #define LED_STATE_ON          1
@@ -56,8 +66,6 @@ static void all_rcc_clk_enable(void)
 
 void board_init(void)
 {
-
-
   /* Configure the system clock to 48 MHz */
   RCC_ClkInitTypeDef RCC_ClkInitStruct;
   RCC_OscInitTypeDef RCC_OscInitStruct;

hw/bsp/stm32f072disco/stm32f072disco.c

@@ -25,9 +25,19 @@
  */
 
 #include "../board.h"
-
 #include "stm32f0xx_hal.h"
 
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USB_IRQHandler(void)
+{
+  tud_irq_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
 #define LED_PORT              GPIOC
 #define LED_PIN               GPIO_PIN_6
 #define LED_STATE_ON          1

hw/bsp/stm32f103bluepill/stm32f103bluepill.c

@@ -25,9 +25,29 @@
  */
 
 #include "../board.h"
-
 #include "stm32f1xx_hal.h"
 
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USB_HP_IRQHandler(void)
+{
+  tud_irq_handler(0);
+}
+
+void USB_LP_IRQHandler(void)
+{
+  tud_irq_handler(0);
+}
+
+void USBWakeUp_IRQHandler(void)
+{
+  tud_irq_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
 #define LED_PORT              GPIOC
 #define LED_PIN               GPIO_PIN_13
 #define LED_STATE_ON          0

hw/bsp/stm32f303disco/stm32f303disco.c

@@ -25,9 +25,41 @@
  */
 
 #include "../board.h"
-
 #include "stm32f3xx_hal.h"
 
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+
+// USB defaults to using interrupts 19, 20, and 42 (based on SYSCFG_CFGR1.USB_IT_RMP)
+// FIXME: Do all three need to be handled, or just the LP one?
+// USB high-priority interrupt (Channel 19): Triggered only by a correct
+// transfer event for isochronous and double-buffer bulk transfer to reach
+// the highest possible transfer rate.
+void USB_HP_CAN_TX_IRQHandler(void)
+{
+  tud_irq_handler(0);
+}
+
+// USB low-priority interrupt (Channel 20): Triggered by all USB events
+// (Correct transfer, USB reset, etc.). The firmware has to check the
+// interrupt source before serving the interrupt.
+void USB_LP_CAN_RX0_IRQHandler(void)
+{
+  tud_irq_handler(0);
+}
+
+// USB wakeup interrupt (Channel 42): Triggered by the wakeup event from the USB
+// Suspend mode.
+void USBWakeUp_IRQHandler(void)
+{
+  tud_irq_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+
 #define LED_PORT              GPIOE
 #define LED_PIN               GPIO_PIN_9
 #define LED_STATE_ON          1

hw/bsp/stm32l0538disco/stm32l0538disco.c

@@ -25,9 +25,19 @@
  */
 
 #include "../board.h"
-
 #include "stm32l0xx_hal.h"
 
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USB_IRQHandler(void)
+{
+  tud_irq_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
 #define LED_PORT              GPIOA
 #define LED_PIN               GPIO_PIN_5
 #define LED_STATE_ON          1

src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c

@@ -489,7 +489,9 @@ static void dcd_ep_ctr_handler(void)
   }
 }
 
-static void dcd_fs_irqHandler(void) {
+void dcd_irq_handler(uint8_t rhport) {
+
+  (void) rhport;
 
   uint32_t int_status = USB->ISTR;
   //const uint32_t handled_ints = USB_ISTR_CTR | USB_ISTR_RESET | USB_ISTR_WKUP
@@ -804,57 +806,5 @@ static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, size_t wN
   return true;
 }
 
-
-// Interrupt handlers
-#if CFG_TUSB_MCU == OPT_MCU_STM32F0 || CFG_TUSB_MCU == OPT_MCU_STM32L0
-void USB_IRQHandler(void)
-{
-  dcd_fs_irqHandler();
-}
-
-#elif CFG_TUSB_MCU == OPT_MCU_STM32F1
-void USB_HP_IRQHandler(void)
-{
-  dcd_fs_irqHandler();
-}
-void USB_LP_IRQHandler(void)
-{
-  dcd_fs_irqHandler();
-}
-void USBWakeUp_IRQHandler(void)
-{
-  dcd_fs_irqHandler();
-}
-
-#elif (CFG_TUSB_MCU) == (OPT_MCU_STM32F3)
-// USB defaults to using interrupts 19, 20, and 42 (based on SYSCFG_CFGR1.USB_IT_RMP)
-// FIXME: Do all three need to be handled, or just the LP one?
-// USB high-priority interrupt (Channel 19): Triggered only by a correct
-// transfer event for isochronous and double-buffer bulk transfer to reach
-// the highest possible transfer rate.
-void USB_HP_CAN_TX_IRQHandler(void)
-{
-  dcd_fs_irqHandler();
-}
-
-// USB low-priority interrupt (Channel 20): Triggered by all USB events
-// (Correct transfer, USB reset, etc.). The firmware has to check the
-// interrupt source before serving the interrupt.
-void USB_LP_CAN_RX0_IRQHandler(void)
-{
-  dcd_fs_irqHandler();
-}
-
-// USB wakeup interrupt (Channel 42): Triggered by the wakeup event from the USB
-// Suspend mode.
-void USBWakeUp_IRQHandler(void)
-{
-  dcd_fs_irqHandler();
-}
-
-#else
-  #error Which IRQ handler do you need?
-#endif
-
 #endif