try to add lpc4357usb board

demos/bsp/boards/board.h

@@ -73,6 +73,8 @@
 #define BOARD_HITEX4350             6
 #define BOARD_LPCXPRESSO1769        7
 
+#define BOARD_LPC4357USB            8
+
 //--------------------------------------------------------------------+
 // PRINTF TARGET DEFINE
 //--------------------------------------------------------------------+
@@ -99,6 +101,8 @@
   #include "hitex/board_hitex4350.h"
 #elif BOARD == BOARD_LPCXPRESSO1769
   #include "lpcxpresso/board_lpcxpresso1769.h"
+#elif BOARD == BOARD_LPC4357USB
+  #include "microbuilder/board_lpc4357usb.h"
 #else
   #error BOARD is not defined or supported yet
 #endif

demos/bsp/boards/embedded_artists/board_ea4357.c

@@ -42,9 +42,9 @@
 
 
 #define BOARD_UART_PORT           LPC_USART0
-#define BOARD_UART_PIN_PORT 0x0f
+#define BOARD_UART_PIN_PORT       0x0f
-#define BOARD_UART_PIN_TX   10 // PF.10 : UART0_TXD
+#define BOARD_UART_PIN_TX         10 // PF.10 : UART0_TXD
-#define BOARD_UART_PIN_RX   11 // PF.11 : UART0_RXD
+#define BOARD_UART_PIN_RX         11 // PF.11 : UART0_RXD
 
 void board_init(void)
 {

demos/bsp/boards/microbuilder/board_lpc4357usb.c

@@ -0,0 +1,123 @@
+/**************************************************************************/
+/*!
+    @file     board_lpc4357usb.c
+    @author   hathach (tinyusb.org)
+
+    @section LICENSE
+
+    Software License Agreement (BSD License)
+
+    Copyright (c) 2013, hathach (tinyusb.org)
+    All rights reserved.
+
+    Redistribution and use in source and binary forms, with or without
+    modification, are permitted provided that the following conditions are met:
+    1. Redistributions of source code must retain the above copyright
+    notice, this list of conditions and the following disclaimer.
+    2. Redistributions in binary form must reproduce the above copyright
+    notice, this list of conditions and the following disclaimer in the
+    documentation and/or other materials provided with the distribution.
+    3. Neither the name of the copyright holders nor the
+    names of its contributors may be used to endorse or promote products
+    derived from this software without specific prior written permission.
+
+    THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
+    EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+    WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+    DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
+    DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+    (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+    LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+    ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+    (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+    SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+    This file is part of the tinyusb stack.
+*/
+/**************************************************************************/
+
+#include "../board.h"
+
+#if BOARD == BOARD_LPC4357USB
+
+#define BOARD_MAX_LEDS  1
+const static struct {
+  uint8_t port;
+  uint8_t pin;
+}leds[BOARD_MAX_LEDS] = { {6, 1} };
+
+#define BOARD_UART_PORT           LPC_USART0
+#define BOARD_UART_PIN_PORT       0x0f
+#define BOARD_UART_PIN_TX         10 // PF.10 : UART0_TXD
+#define BOARD_UART_PIN_RX         11 // PF.11 : UART0_RXD
+
+
+void board_init(void)
+{
+  SystemInit();
+  CGU_Init();
+	SysTick_Config( CGU_GetPCLKFrequency(CGU_PERIPHERAL_M4CORE)/CFG_TICKS_PER_SECOND );	/* 1 ms Timer */
+
+	//------------- USB Bus power HOST ONLY-------------//
+//	scu_pinmux(0x1, 7, MD_PUP | MD_EZI, FUNC4);	// P1_7 USB0_PWR_EN, USB0 VBus function Xplorer
+//
+//	scu_pinmux(0x2, 6, MD_PUP | MD_EZI, FUNC4); // P2_6 is configured as GPIO5[6] for USB1_PWR_EN
+//	GPIO_SetDir   (5, BIT_(6), 1);              // GPIO5[6] is output
+//	GPIO_SetValue (5, BIT_(6));                 // GPIO5[6] output high
+
+	//------------- Led Init -------------//
+	for (uint8_t i=0; i<BOARD_MAX_LEDS; i++)
+	{
+	  scu_pinmux(leds[i].port, leds[i].pin, MD_PUP|MD_EZI|MD_ZI, FUNC4);
+	  GPIO_SetDir(leds[i].port, BIT_(leds[i].pin), 1); // output
+	}
+
+#if CFG_UART_ENABLE
+  //------------- UART init -------------//
+	scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_TX, MD_PDN             , FUNC1);
+	scu_pinmux(BOARD_UART_PIN_PORT, BOARD_UART_PIN_RX, MD_PLN|MD_EZI|MD_ZI, FUNC1);
+
+	UART_CFG_Type UARTConfigStruct;
+  UART_ConfigStructInit(&UARTConfigStruct);
+	UARTConfigStruct.Baud_rate = CFG_UART_BAUDRATE;
+	UARTConfigStruct.Clock_Speed = 0;
+
+	UART_Init(BOARD_UART_PORT, &UARTConfigStruct);
+	UART_TxCmd(BOARD_UART_PORT, ENABLE); // Enable UART Transmit
+#endif
+
+}
+
+//--------------------------------------------------------------------+
+// LEDS
+//--------------------------------------------------------------------+
+void board_leds(uint32_t on_mask, uint32_t off_mask)
+{
+  for (uint32_t i=0; i<BOARD_MAX_LEDS; i++)
+  {
+    if ( on_mask & BIT_(i))
+    {
+      GPIO_SetValue(leds[i].port, BIT_(leds[i].pin));
+    }else if ( off_mask & BIT_(i)) // on_mask take precedence over off_mask
+    {
+      GPIO_ClearValue(leds[i].port, BIT_(leds[i].pin));
+    }
+  }
+}
+
+//--------------------------------------------------------------------+
+// UART
+//--------------------------------------------------------------------+
+#if CFG_UART_ENABLE
+uint32_t board_uart_send(uint8_t *buffer, uint32_t length)
+{
+  return UART_Send(BOARD_UART_PORT, buffer, length, BLOCKING);
+}
+
+uint32_t board_uart_recv(uint8_t *buffer, uint32_t length)
+{
+  return UART_Receive(BOARD_UART_PORT, buffer, length, BLOCKING);
+}
+#endif
+
+#endif

demos/bsp/boards/microbuilder/board_lpc4357usb.h

@@ -0,0 +1,67 @@
+/**************************************************************************/
+/*!
+    @file     board_lpc4357usb.h
+    @author   hathach (tinyusb.org)
+
+    @section LICENSE
+
+    Software License Agreement (BSD License)
+
+    Copyright (c) 2013, hathach (tinyusb.org)
+    All rights reserved.
+
+    Redistribution and use in source and binary forms, with or without
+    modification, are permitted provided that the following conditions are met:
+    1. Redistributions of source code must retain the above copyright
+    notice, this list of conditions and the following disclaimer.
+    2. Redistributions in binary form must reproduce the above copyright
+    notice, this list of conditions and the following disclaimer in the
+    documentation and/or other materials provided with the distribution.
+    3. Neither the name of the copyright holders nor the
+    names of its contributors may be used to endorse or promote products
+    derived from this software without specific prior written permission.
+
+    THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
+    EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+    WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+    DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
+    DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+    (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+    LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+    ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+    (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+    SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+    This file is part of the tinyusb stack.
+*/
+/**************************************************************************/
+
+/** \ingroup TBD
+ *  \defgroup TBD
+ *  \brief TBD
+ *
+ *  @{
+ */
+
+#ifndef _TUSB_BOARD_LPC4357USB_H_
+#define _TUSB_BOARD_LPC4357USB_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#include "LPC43xx.h"
+#include "lpc43xx_scu.h"
+#include "lpc43xx_cgu.h"
+#include "lpc43xx_gpio.h"
+#include "lpc43xx_uart.h"
+
+#define CFG_PRINTF_TARGET PRINTF_TARGET_DEBUG_CONSOLE // PRINTF_TARGET_UART
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif /* _TUSB_BOARD_LPC4357USB_H_ */
+
+/** @} */