* restricted/pr/403:
Correct record header size in case of TLS
Don't allocate space for DTLS header if DTLS is disabled
Improve debugging output
Adapt ChangeLog
Add run-time check for handshake message size in ssl_write_record
Add run-time check for record content size in ssl_encrypt_buf
Add compile-time checks for size of record content and payload
* development:
Don't split error code description across multiple lines
Register new error code in error.h
Move deprecation to separate section in ChangeLog
Extend scope of ERR_RSA_UNSUPPORTED_OPERATION error code
Adapt RSA test suite
Adapt ChangeLog
Deprecate usage of RSA primitives with wrong key type
* restricted/pr/397:
Don't split error code description across multiple lines
Register new error code in error.h
Move deprecation to separate section in ChangeLog
Extend scope of ERR_RSA_UNSUPPORTED_OPERATION error code
Adapt RSA test suite
Adapt ChangeLog
Deprecate usage of RSA primitives with wrong key type
In a previous PR (Fix heap corruption in implementation of truncated HMAC
extension #425) the place where MAC is computed was changed from the end of
the SSL I/O buffer to a local buffer (then (part of) the content of the local
buffer is either copied to the output buffer of compare to the input buffer).
Unfortunately, this change was made only for TLS 1.0 and later, leaving SSL
3.0 in an inconsistent state due to ssl_mac() still writing to the old,
hard-coded location, which, for MAC verification, resulted in later comparing
the end of the input buffer (containing the computed MAC) to the local buffer
(uninitialised), most likely resulting in MAC verification failure, hence no
interop (even with ourselves).
This commit completes the move to using a local buffer by using this strategy
for SSL 3.0 too. Fortunately ssl_mac() was static so it's not a problem to
change its signature.
Fix missing definition of mbedtls_zeroize when MBEDTLS_FS_IO is
disabled in the configuration.
Introduced by e7707228b4c696549017fbf0fcb5aaae552e4bde
Merge remote-tracking branch 'upstream-public/pr/1062' into development
In case truncated HMAC must be used but the Mbed TLS peer hasn't been updated
yet, one can use the compile-time option MBEDTLS_SSL_TRUNCATED_HMAC_COMPAT to
temporarily fall back to the old, non-compliant implementation of the truncated
HMAC extension.
The truncated HMAC extension as described in
https://tools.ietf.org/html/rfc6066.html#section-7 specifies that when truncated
HMAC is used, only the HMAC output should be truncated, while the HMAC key
generation stays unmodified. This commit fixes Mbed TLS's behavior of also
truncating the key, potentially leading to compatibility issues with peers
running other stacks than Mbed TLS.
Details:
The keys for the MAC are pieces of the keyblock that's generated from the
master secret in `mbedtls_ssl_derive_keys` through the PRF, their size being
specified as the size of the digest used for the MAC, regardless of whether
truncated HMAC is enabled or not.
/----- MD size ------\ /------- MD size ----\
Keyblock +----------------------+----------------------+------------------+---
now | MAC enc key | MAC dec key | Enc key | ...
(correct) +----------------------+----------------------+------------------+---
In the previous code, when truncated HMAC was enabled, the HMAC keys
were truncated to 10 bytes:
/-10 bytes-\ /-10 bytes-\
Keyblock +-------------+-------------+------------------+---
previously | MAC enc key | MAC dec key | Enc key | ...
(wrong) +-------------+-------------+------------------+---
The reason for this was that a single variable `transform->maclen` was used for
both the keysize and the size of the final MAC, and its value was reduced from
the MD size to 10 bytes in case truncated HMAC was negotiated.
This commit fixes this by introducing a temporary variable `mac_key_len` which
permanently holds the MD size irrespective of the presence of truncated HMAC,
and using this temporary to obtain the MAC key chunks from the keyblock.
Previously, MAC validation for an incoming record proceeded as follows:
1) Make a copy of the MAC contained in the record;
2) Compute the expected MAC in place, overwriting the presented one;
3) Compare both.
This resulted in a record buffer overflow if truncated MAC was used, as in this
case the record buffer only reserved 10 bytes for the MAC, but the MAC
computation routine in 2) always wrote a full digest.
For specially crafted records, this could be used to perform a controlled write of
up to 6 bytes past the boundary of the heap buffer holding the record, thereby
corrupting the heap structures and potentially leading to a crash or remote code
execution.
This commit fixes this by making the following change:
1) Compute the expected MAC in a temporary buffer that has the size of the
underlying message digest.
2) Compare to this to the MAC contained in the record, potentially
restricting to the first 10 bytes if truncated HMAC is used.
A similar fix is applied to the encryption routine `ssl_encrypt_buf`.
* development: (30 commits)
update README file (#1144)
Fix typo in asn1.h
Improve leap year test names in x509parse.data
Correctly handle leap year in x509_date_is_valid()
Renegotiation: Add tests for SigAlg ext parsing
Parse Signature Algorithm ext when renegotiating
Minor style fix
config.pl get: be better behaved
config.pl get: don't rewrite config.h; detect write errors
Fixed "config.pl get" for options with no value
Fix typo and bracketing in macro args
Ensure failed test_suite output is sent to stdout
Remove use of GNU sed features from ssl-opt.sh
Fix typos in ssl-opt.sh comments
Add ssl-opt.sh test to check gmt_unix_time is good
Extend ssl-opt.h so that run_test takes function
Always print gmt_unix_time in TLS client
Restored note about using minimum functionality in makefiles
Note in README that GNU make is required
Fix changelog for ssl_server2.c usage fix
...
Fix the x509_get_subject_alt_name() function to not accept invalid
tags. The problem was that the ASN.1 class for tags consists of two
bits. Simply doing bit-wise and of the CONTEXT_SPECIFIC macro with the
input tag has the potential of accepting tag values 0x10 (private)
which would indicate that the certificate has an incorrect format.
